Three side heating elements. Standard double wall fabrication. Inner chamber made of anodized aluminium or highly polished stainless steel sheet. Exterior fabricated out of thick mild steel sheet duly finished in stoved enamel off-white paint or paste mat finish colour combinations. The gap between the walls is filled with- special grade glass -wool for heat insulation. Inner chamber is ribbed for placing shelves at convenient levels. P rovided with two or three removable shelves. special elegant door closing device has bee n provided. Nichrome wire heating elements provided on three sides attain quick and uniform heating in range of 50ºC to 250ºC ±1ºC controlled by capillary type thermostat. L -shaped thermometer is built -in type. Control panel is provided with selector switch of high or low rates of power , thermostat control knob and indicators for mains & thermostat. Supplied with cord and plug . The equipment is suitable to operate on 220 V olts 50Hz, single phase AC.

Optional Accessories:: (Extra Cost)

Double wall extra sturdy construction on thick angle iron frame with both inner and outer walls of thick PCRC sheet duly protected against rusting and corrosion. The exterior is finished in ash-grey hammer tone. The gap is filled with special grade glass wool for heating insulation. A heavy duty constantly running blower provided to maintain uniform constant temperature in the chamber. Front door mounted on heavy hinges is double walled. Temperature is controlled by a capillary type thermostat with range from 50º C to 250ºC ±2ºC to 3ºC workable on 220Volts, 50Hz, single or three phase AC. Provided with two trays. The panel provided with mains indicator, heater indicator, temperature control knob and dial type thermometer, Cord and plug.

Chamber sizes in mm.
a) 900x600x600 b) 1200x900x600 c) 1500x900x600 b) 1800x1200x900.

Optional Accessories: (Extra Cost)
A) Digital temperature indicator -cum-controller.

Double wall fabricated. Inner chamber made out of richly anodized aluminium or highly stoving enamel paint or mat finished paste colour combinations. The gap is filled with special glass wool. Double wall door with double glass window for observation in the chamber. Temperature range 5ºC above ambient to 80ºC ±2ºC controlled by a thermostat. L-shaped thermometer is provided for taking temperature reading. Panel is provided with pilot lamps for main heaters, On-Off switch, temperature Control knob etc. The equipment workable on 220Volts AC 50 Hz single phase. Heating is achieved from 3 sides. Perforated removable shelves also provided.

Optional Accessories:: (Extra Cost)

Double wall construction, inner being made out of highly polished thick stainless steel and outer made out thick mild steel sheet finished in stoving white enamel paint or staple mat colour combinations. The gap is filled with special glass wool for temperature insulation. The bath is provided with a drain cock to easily drain out the water and clean the chamber when required. A pyramidal shaped cover is prov ided. Immersion type heating elements are fitted at bottom. temperature range 5ºC above ambient to 80ºC with accuracy ±0.5ºC to 1ºC is controlled by capillary thermostat regulated by a graduated knob on the panel, which is also provided with pilot lamp etc. The equipments is workable on 220V olts, 50Hz single phase AC. The baths are supplied without thermometer and stirring arrangement.

Working chamber sizes in mm (Stainless Steel)
a) 300 x 175 x 175 b)300 x 250 x 175 c)375 x 300 x 175 d) 450 x 300 x 175

Optional Accessories: (Extra Cost) : Stirring arrangement with S .S. rod and blades, Digital temperature indicator , Digital indicator -cum-temperature controller .

Construction as per model 6729 but with glass windows on both opposite sides, for observation. temperature controlled by mercury contact thermometer with a sensitivity of 2ºC. Suitable for precision laboratory activities requiring constant temperature with high degree of accuracy . Complete with stirrer with speed control regulator workable on 220Volts Hz single phase A C.

Chamber Size in mm :
a) 425x250x225 b) 450x375x375 c) 600x450x450

Suitable to spread wax section ribbons after microtomy to get wrinkle free specimen for staining. Double wall round construction. Inner chamber black anodized aluminium and outer made out of mild steel duty finished in stoving white enamel paint. F or drying wet slides. temperature range 5ºC above ambient to 70ºC ±2ºC. Immersion type heating elements attain the controlled temperature regulated by a capillary thermostat. P anel provided with thermo-regulator knob, pilot lamp and is supplied with cord & plug. equipment workable on 220V olts Hz single phase A C.

Chamber sizes in mm :
a) 200x75               b) 250x125

Double wall construction. Inner chamber made of highly polished stainless steel or copper sheet and outer made of mild steel duly finished in stoving enamel. T emperature range 50ºC to 250ºC ±2ºC is controlled by a thermostat. The oil bath is suitable for a wide range of applications like oxidation stability test on oils, other tests in which high temperature control is required. Supplied complete with stirrer , diffuser shelves, cover etc. panel provided with On- Off switch, pilot lamps thermostatic control knob etc.

Chamber size in mm : (Stainless Steel)
a) 250x250x250 b) 300x300x250 c) 350x250x250

Optional Accessories: (Extra Cost) :
Mercury contact thermometer and relay with accuracy better than 1ºC, Digital temperature indicator, Digital temperature indicator-cum- controller instead of thermostatic control and L -shaped thermometer .

Useful for dual purpose. It is a combination of serological and routine rectangular water bath with holes and co -centric rings. Standard double wall construction. Inner chamber made out highly polished stainless steel sheet and exterior made out of thick mild steel duly finished in stoving enamel paint, The gap between the two walls is filled with special glass wool for temperature insulation. Immersion heaters are provided for heating to attain temperature range from 5ºC above ambient to 90ºC ±1ºC ans is controlled by capillary type thermostat, controlled by thermostat knob on the panel. Supplied complete with plug & cord. The equipment works on 220V olts 50Hz single phase A C. Equipments has been provided with two covers, one of a pyramidal shape and the other with 75mm diameter holes with co -centric rings. The chamber is provided with drain cock to easily drain out the water whenever required.

Optional Accessories:: (Extra Cost)

a) Standard double walled construction. Inner chamber made out of thick highly polished stainless steel sheet. T emperature range 5ºC to 90ºC and controlled by sensitive Mercury contact thermometer with an accuracy of ±0.2ºC. F itted a stirrer and speed regulator . Chamber size : 500 x 250 x 250mm.
b) As above but refrigerated bath fitted with a FHP pump for circulating t he cord liquid to the external equipment.

Optional Accessories : (Extra Cost) i) Digital temperature controller -cum-indicator instead of contact thermometer .

Useful for studies on tissue metabolism, enzymes and protein coagulation and other experiments demanding shaking at constant speed under controlled temperature conditions. Double walled construction, inner chamber made out of thick highly polished stainless steel sheet and outer made out of thick mild steel duty finished in stoving enamel paint. The lid made of stainless steel. The gap between the two chambers filled with glass wool to pre vent loss of heat. The temperature is achieved by superior immersion heater and is controlled by capillary type thermostat from ambient to 90ºC ±0.5ºC. The shaking mechanism is fitted with variable speed motor coupled to shaking tray wor k in on rollers. Shaking speed is controlled from 40 to 140 cycles per minute. Shaking tray can hold either test-tubes or flasks of 25ml. or 50ml. or 100ml. capacity . Front panel includes on- off switch, shaking mechanism indicator , speed control, thermostat control etc. L-Shaped thermometer is provided to indicate inside temperature. Equipment to work on 220V olts, 50Hz single phase A C.

Inner chamber sizes in mm :
a) 275 x 275 x75 b) 275x275x150 c) 400x300x150
Optional Accessories : (Extra Cost) Shaking Tray for 25ml, 50ml and 100ml

Wall hanging casted aluminium vessel is electrically operated for getting pyrogen-free distilled water automatically . Wall hanging space saving arrangement is provided. The condenser is seamless. F itted with automatic ejection device which operates automatically when water vessel gets dried. The baffle cup and condenser are made out of thick stainless steel sheet.

Output Capacity Per Hour approx. : a) 2-3 litre          b) 4-5 litre

Double wall construction having both made out of highly polished stainle ss steel sheet. The gap between the two is filled with glass wool for heat insulation. It is easy to handle table model working on 220 V olts, 50 Hz single phase A C.

Output Capacity per hour (Approximately) :
a) 4-5 litre b) 8-9 litre c) 15-16 d) 25-26 litre

Outer shell out of thick mild steel duly finished in attractive stoving enamel paint. F itted with grooved refractory for supporting the heating elements made out of kanthal wire and are easily replaceable. Maximum temperature 1000ºC with working temperature 940ºC controlled by energy regulator . Complete with indicators, pyrometer , thermocouple - thermal fuse etc. workable on 220 V olts, 50 Hz single phase A C.

Optional Accessories:: (Extra Cost) Digital Temperature indicator -cum-controller instead of energy regulator and pyrometer .

Specification as model 6760 but maximum temperature 1150ºC with working temperature 1100ºC. Complete in all respects as above.

Optional Accessories: (Extra Cost) Digital temperature indicator -cum-controller instead of energy regulator & pyrometer .

Compact stirring device utilising a rotating magnetic field applied from below the container. The stirring is accomplished by a Teflon rotor placed in the liquid to be stirred. Complete with pilot lamp, plug cord, continuously variable speed regulator. The body is made of mild steel duly finished in stoving enamel and mounted with stainless steel top which serves as a hot plate. Stirring and heating units are properly insulated. In model with heating system temperature is controlled by a energy regulator. An electronic speed controller is also provided. The equipment works on 220V AC 50Hz single phase.

Heavy stable cast iron base duly painted with mild steel chrome plated upright provided with strong adjustable clamps to hold motor with stirring rod of stainless steel with T eflon grinder and clamp to hold tissue homogenising vessel of borosilicate gla ss which is also adjustable. Speed variable through a control unit to work on 220 V olts, 50 Hz single phase AC. Motor used is of 1/20 HP

Body in made of one piece aluminium ans is logged with special mineral wool. The panel is provided with on- off switch, energy control knob, pilot lamp. etc. Provided with joint less hand knitted heating nets of glass yarn capable of with standing high temperature up to 400ºC. Single individual size up to 5 liters capacity containers are available. Supplied complete with cord & plug to work on 220 V olts, 50 Hz single phase AC. Single circuit system has been adopted.

Note : Other sizes, capacities, multiple models and spare heating mantles can be offered on demand.

Specification as above but plates is rectangular in shape.
Following standard sizes are available:

Note: Other sizes can be offered on demand.
Optional Accessories: (Extra Cost)
a) Energy regulator .
b) Digital temperature Indicator -cum-Controller.

A versatile equipment to heat slides with fresh microtomed sections to attain maximum flatness before staining . Temperature range ambient temperature to 70ºC i.e. below the melting point of wax. the temperature is thermostatically controlled. The body is made out of thick mild steel duly finished in stoving enamel and top is made of highly polished copper or stainless steel sheet. Complete with thermostatic control knob, ind icator lamp, plug & cord etc. T o work on 220V olts, 50Hz single phase A.C

Standard sizes available :
a) 300x250mm
b) 400x250mm.
c) 450x300mm

Heavy cast - iron base with sturdy construction with two side arms for holding flask. A heavy duty fractional motor with variable speed through continuously variable speed controller is provided. The holders can hold flasks of capacity 100 to 1000ml. Supplied complete with cord & plug etc. to work on 220 V A C 50 Hz single phase. Speed 80-280 oscillations per minute.
a) Model to hold 4 flasks.
b) Model to hold 8 flasks.
c) Model to hold 16 flasks.

Optional Accessories : Automatic 0- 60 minutes timer .

Designed for shaking kahh racks, bottles, flasks of different sizes by adjusting compartments. F itted with heavy duty motor to work on 220 V A C 50 Hz single phase. the rate of motion is adjustable mechanically by belt tension. Speed is fixed in same models to approx. 275 or variable as detailed below.

Optional Accessories:(Extra Cost)0-60 minutes timer. Shaking machines of other specification can be offered on demand.

Other sizes & capacities can be offered on demand.
Optional Accessories: (Extra cost) 0-60 minutes timer .

Electrically operated, dome type, sturdy, stable heavy body with resiliently mounted motor working on 220 Volts, 50 Hz, single phase AC for vibration free performance with built in 5 speed regulator and a non-removable swing out rotor. Complete with tube carriers. Maximum speed 3500 RPM. Neatly finished in stoving enamel paint.
a) 4x15 ml. tubes.
b) 6x15 ml. tubes.
c) 8x15 ml. tubes.

Optional Accessories : (Extra Cost) Automatic 0-60 minutes timer .

Electrically operated, R ectangular body sturdy , stable heavy body with resiliently mounted motor working on 220 V olts, 50Hz, single phase A C for vibration free performance with built in 5 speed regulator and a non-removable swing out rotor . Complete with tube carriers. Maximum speed 3500 RPM. Neatly finished in stoving enamel paint.
a) 4x15 ml. tubes.
b) 6x15 ml. tubes.
c) 8x15 ml. tubes.

Optional Accessories : (Extra Cost) Automatic 0-60 minutes timer .

I) Single wal , chamber made of stainless steel. Provided with individual on-off switches but having one energy regulator to control all units. Units without glass parts.
1. A unit of 3 baths.
2. A unit of 6 baths.

II) Double wall, inner chamber made of stainless steel, other specification as above.
Optional Accessories: (Extra cost) R egulator can be provided against extra cost for all above units.
All above units work on 220 Volt A C 50Hz single phase.

Motor driven, oil sealed pump mounted on heavy base. It is driven by V-belt at speed up to 400 RPM. Choice of single and double stage available creating ultimate vacuum of 0.01 mm of high column and 0.00mm of Hg column respectively . The pump is to work on 220Volts AC. Capacities available are :

Optional Accessories: (Extra Cost) : Vacuum gauge, Belt Guard, Moisture trap, Non-return valve and Air blast.

Made out of mild steel duly finished in stoving enamel paint. Other metallic parts are chrome plated. Following units are available :
a) Kjeldhal Digestion Units
b) Kjeldhal Distillation Units

Useful for estimation of nitrogen contents in substance by digestion in 300 & 500 ml flasks. Provided (optional) with fume duct made of lead and pair of hangers. T o work on 220Volts, AC. Individual on- off switches and one energy controller for all units is provided.
1) Unit of 3 tests (Heater type)
2) Unit of 6 tests (Heater type)
3) Unit of 3 tests (Mantle type)
4) Unit of 6 tests (Mantle type)

Optional Accessories: (Extra Cost)
i) Fume duct made of lead or Borosilicate glass.
ii) Energy regulator .

Asbestos tops mounted on mild steel tubular stand. Provided with condenser clamps and water manifold. Other specification as above.
1) Unit of 3 tests (Heater type)
2) Unit of 6 tests (Heater type)
3) Unit of 3 tests (Mantle type)
4) Unit of 6 tests (Mantle type)

Optional Accessories: (Extra Cost) Energy regulator.

One single mild steel tubular stand is provided with two heating shelves, one above the other. A fume duct holder and a heating box are supplied for digestion unit. The heating units have individual on- off switches. In the upper portion another heating unit with a condenser rack is provided. the unit is workable on 220V olts AC. Complete with cord & plug etc.
1) Unit of 3 tests (Heater type)
2) Unit of 6 tests (Heater type)
3) Unit of 3 tests (Mantle type)
4) Unit of 6 tests (Mantle type)

Optional Accessories: (Extra Cost) Fume duct made of lead or Borosilicate glass. Sunvic energy regulator. Note : All above units are without glass parts.

Electrically heated sterilizer under saturated steam of adjustable pressure of 10 to 20 psi. Double walled construction with boiler & steam jacket made of thick stainless steel and gap is filled with high grade glass wool to bring the temperature loss to a m inimal level. The outer chamber is made out of thick mild steel. The lid is made of thick stainless steel plate (joint less) or gunmetal plate and can be sealed by a joint less neoprene rubber gasket by wing nuts through hinged bolts by engaging slotted lugs on rim of the cover. Provided with dial pressure gauge, air/steam release cock., spring loaded safety valve adjustable to any required point from 10psi to 20psi with accuracy ±3 psi. A drain cock has also been provided. a double safety valve has also been provided along with water inlet. Supplied complete but without dressing bins. 

Optional Accessories: (Extra Cost)
i) Automatic low-water level cut-off device,
ii) Pressure control switch,
iii) Radial lock (for models d, e & f)
iv) Dressing bins for various sizes
v). Water level arrangement.

Specification as in vertical model but presented in a horizontal position and without steam jacket. The outer body made of mild steel , inner chamber made of stainless steel.

Optional Accessories: (Extra Cost) i) Pressure Gauge ii)Automatic low water level cut -off device. iii)P ressure control switch.

Specification as above but double chamber. For cooling a sealed compressor unit has been provided below the chamber to work independently. Each chamber size : 555x910x605mm
a) Heating and cooling in separate chambers : Chamber made of anodized aluminium.
b)As in (a) but chamber made of stainless steel.
c)Heating & cooling in both chamber and chambers made of anodized aluminium.
d) As in (c) but chambers made of stainless steel.

Optional Accessories: (Extra Cost)
i) Automatic 0-24 hours timer to regulate cyclic illumination conditions.
ii) Automatic voltage stabilizer - 3KV A (must)

Double walled construction, inner made out of richly anodized aluminium or stainless steel sheet and outer that of thick mild steel duly finished in stoving enamel paint. Gap is filled with glass wool for temperature, insulation. A circulation fan has been provided to maintain uniform temperature & humidity through out the chamber . Nichrome heating elements are provided to heat the chamber effectively . Temperature range from ambient to 60ºC is controlled by a thermostat. L-shaped thermometer is provided to indicate temperature in the chamber . Humidity is created by a generating steam by heating water in a stainless steel reservoir by an immersion heater and subsequent condensation in circulating air . the humidity is controlled by a humidistant from atmospheric humidity to 95% ±3% RH. The double walled door has bee n provided with a double wall clear glass window for observation in the chamber without opening the door and disturbing chamber conditions. A control panel has been provided on left of the body and is provided with all control switches phase. Supplied complete with cord & plug but without hygrometer .

OPTIONAL : (Extra Cost) :
i)Hygrometer (Humidity indicator),
ii) Digital temperature Controller-cum-Indicator ,
iii) Digital temperature indicator,
iv) Automatic voltage stabilizer 3 KVA.

Models: Chamber size :
a) 455 x 455x 455 mm. (Ht.)
b) 455 x 455x710 mm. (Ht.)
c) 605 x 605x605 mm. (Ht.)
d) 605 x 604x 910 mm. (Ht.)

Environmental Chamber, General specification as above but with added specification for low tem perature control & humidity. The inner working chamber is made out of stainless steel. The temperature can be controlled from 5ºC-55ºC ±2ºC and humidity from 55% to 95% ±5% Rh through an electronic digital controller-cum-indicator. Temp. below ambient is controlled by hermetically sealed compressor complete with accessories heated by immersion heaters are provided to create humidity. Complete with all accessories. Control panel provided with control switches and indicators. The equipment to work on 220V olts, AC 50Hz, single phase. Provided with plug & cord but without hygrometer.

Models: Chamber size in mm.
a) 455 x 455 x 710 mm. (Ht.)
b) 605 x 605 x 605 mm. (Ht.)
c) 605 x 605 x 910 mm. (Ht.)

Optional Accessories: (Extra Cost)
i) Digital type hygrometer (Humidity indicator)
ii) Automatic voltage stabilizer 3 KV A (must)

Specification as above but capacity 70 bags or 35 bottles and without door operation and temperature fluctuation alarms.

Optional Accessories:: (Extra cost) Automatic voltage stabilizer 3KVA (must)

Note: Vaccine Freezers, Semen F reezers, Plate Freezers and Test Tube freezers are also offered on demand.

These plasma storage cabinets are designed for quick freezing and storing of plasma and related blood components at desired low temperatures up -35ºC. All models feature integrated control panel with digital temperature indicator cum controller and temperature recorder . Constructed of double walls, the exterior is made of powder coated sheet, steel finish while the inner chamber is made of stainless steel. The unit is mounted on castor wheels for ease of mobility . Plasma F reezers are available in horizontal and vertical versions. Temperature of F reezer also reduce up to -70ºC as per requirement.

Special F eatures :
• Low temperature up -to -35ºC.
• Stainless Steel inner chamber
• Extremely efficient insulation to minimise heat loss.
• Digital temperature indicator cum controller with audio visual alarm.
• Inside acrylic door to avoid temperature loss.

Preprogrameble collective device to draw precise volume of blood from donor . Fitted with uniformly oscillating collection tray to agitate blood during collection and ensure uniformly mixing of blood anti coagulant. Oscillation speed: 10RPM.

Digital display indication :
• The volume of blood in the blood bag during collection.
• Set volume, the volume which is to be collected.
• Flow of blood, i.e. normal, high or low and indicating buzzer to abnormal flow .
• Time taken for collection of set volume and running time also.
• Automatic termination of blood collection when blood volume collected reaches preset volume.
Pause function for temporary stopping of blood collection in process but at that time oscillation will be continue.
• Battery operated model also available (Optional model)

Laminar flow principle involves double filtration of air through coarse pr e-filters (up to 5 microns) and Heat filter (down to 0.3 microns) for filtration of biological and particulate contaminants. A constant uni- directional air flow is drawn from atmosphere and passed through pre and heat filters on the work surface. F abricated out of reinforced ply board which is clab in from out side in laminated sheet and inner exposed areas are finished in epoxy paint. T able top covered with non-glaring laminated sheet or stainless steel sheet (optional). Side panels are fixed and are made out of transparent acrylic sheet. The front door is folding type and made of thick acrylic sheet. (Optional) Stand is built in type or detachable. Blower unit has A U or equivalent motor and is dynamically balanced with minimal sound & vibration level. Fluorescent lighting is also provided. A suitable UV tube is provided for sterilization. An acrylic block type manometer to measure static pressure in the chamber has been installed. T wo way gas tap for gas line has also been provided.

Working chamber sizes in mm.
a) 600x600x600 mm)
b) 900x600x600 mm)
c) 1200x600x600 mm)
d) 1800x600x600 mm)

Optional Accessories: (Extra Cost)
i) Stainless steel table top.
ii) Folding front door made of acrylic sheet.

Useful to conduct experiments on plant growth in controlled environmental c onditions. Double wall construction, inner made of anodized aluminium or stainless steel sheet and outer made of thick mild steel sheet duly finished in stoving enamel paint. the gap is filled with glass wool for insulation of temperature. In addition to a double walled door a full view clear acrylic door is provided for observation in chamber without opening it to avoid disturbance to the inner conditions. Instead a double glass window can be provided in the main door. Adjustable perforated shelves of stainless steel are provided. T emperature range 5ºC to 50ºC ±1ºC is controlled and indicated by a dual electronic digital temperature controller -cum-indicator . Humidity control from 55% to 95% ±2%RH is attained by a humidistant and created in a stainless steel water reservoir set below the chamber and heated by immersion heater . A 0-24 hour timer is also provided. The control panel is provided with indicator lamps, controls etc. Equipment to work on 22 0Volts, AC 50Hz, single phase. Supplied with cord & plug . Arrangement for fluorescent illumination and daylight has also been provided. The control panel is provided with indicator with indicator lamps, controls etc. Equipment to work on 220V olts, 50Hz, AC single phase. Supplied with cord & plug . arrangement for fluorescent illumination and daylight has also been provided.

Optional Accessories: (Extra cost) Automatic voltage stabilizer 3 KV A (must)

Designed to store cadaverous under cool conditions to prevent decomposition. Double walled construction, outer made out thick mild steel sheet duly finished in stoving enamel paint and inner made out of stainless steel sheet. the gap between the two is filled with glass wool for temperature insulation. F ront opening covered with double walled door with magnetic gasket, lock & key and handle. Individual chambers are provided with independent locks with duplicate keys, T rays to carry dead bodies are provided with handles on both ends travel on rollers fitted on ball bearings for smooth movements. The refrigeration unit is fitted on the rear top. T emperature of -20ºC to 4ºC is maintained by hermetically seated compressor unit and is controlled by an automatic electronic digital temperature controller -cum-indicator . Panel is provided with indicators & controllers etc. Complete with cord & plug . The unit work on 220V olts, 50Hz AC single phase.
a) Single Body
b) Two bodies
c) Three bodies

Optional Accessories: (Extra Cost)
i) Outer made of stainless steel sheet
ii) Automatic voltage stabilizer 3KV A